How to install a shade sheet

How to install a shade sail

Before you commence installation it is very important that you consider the well-nigh suitable location for your shade sheet(s) taking into account the factors below. Nosotros've also prepared a 10min video that takes yous through how to install your shade sail.

Before you lot commence installation it is very important that you consider the most suitable location for your shade sail(s) taking into account the following:

  1. Size of the shade canvass(s)&
  2. Strength of existing structures intended to exist anchor points
  3. Ability to insert fixing posts
  4. Location of barbecues
  5. Sunday direction etc

Watch the video

This short video provides a simple overview to installing a triangle and square Coolaroo Shade Canvass.

There could likewise be other factors, specific to your state of affairs, which crave consideration.

Installation Tips

Before you offset

There are some important factors y'all need to consider earlier you go started. Allow's accept a look!

  • Determining The Correct Fixing Points

    Once you accept identified the location for your shade sail(s) it is important to determine the most suitable fixing points for the corners. Some of these fixing points could already exist e.g. pergola/sundeck, large tree, fence post or fascia.

    This stage of the installation is disquisitional. You should ensure all fixing points are structurally sound and if unsure, obtain contained communication from a architect or engineer.

  • Building Approvals

    Prior to installation, check with local regime for any relevant building regulations which may exist.

  • Selecting Fixing Accessories

    There is an extensive range of fixing accessories bachelor to help you lot secure your shade sail(due south). These accessories are readily available from your normal hardware supplier.

    Rope/chain - to extend your shade sheet to a fixing bespeak if required.

    Select the fixing accessories which best suit your own installation.

Attaching to Existing Supports

  • Attaching To Fascia

    If y'all intend to set up your shade sheet to a fascia the use of a Fascia Support is strongly recommended. The Fascia support is used to connect the overhangs of rafters or trusses to fascias ledgers giving a strong connexion betwixt the 2 and improved strength.

  • Attaching to trees

    We recommend that the fixing of shade sails to trees be for TEMPORARY Employ ONLY. The diameter of the tree where the sail volition be fixed must be at least 250mm(9.75").

Attaching to additional supports

  • Mail service Supports

    If boosted posts are required, the use of treated softwood (H5 level handling) is recommended. Hardwood of durability Form 1 can also be used. Your local timber supplier tin assistance you in selection. Post lengths should be calculated taking into account the proposed height of your canvass plus the depth of your footings.

    Steel posts are likewise suitable and are available from either your normal hardware outlet/home eye or your local steel supplier. Steel posts tin be cut to predetermined lengths and painted to a color matching your shade canvass and the environment.

Footings

Measure out centres of basis positions and marker as illustrated. Dig holes 400 mm (sixteen") sq. & 800mm (32") deep.)

  • Firm Ground

    Lay a 100mm (four") depth of 20mm (three/4") dia gravel at the base of the postal service.

  • Soft Ground

    Pour a 100mm (4") depth of physical at the bottom of the hole to provide a solid pad. Insert the posts and, with cord lines, ensure they are in plumb alignment. Temporarily brace the posts.

  • Concreting

    Mix concrete in line with manufacturer'south instructions. These will be labelled conspicuously on the packet. Your supplier will be able to requite you any special communication you lot may require for your own conditions. Pour concrete to the acme of the holes ensuring it is packed well. Ensure the concrete surface is sloping abroad from the posts to assist water drainage. Allow poles to set in concrete for a minimum of 48 hours. Caryatid if required.

Installation

Connect fixing accessories to mounting points as required. Ensure all connections face towards the middle of the sail and are tightly secured. Check again to ensure all mounting points are solid. Lay your shade canvass out and embark the installation.

Tensioning

Using the selected fixing accessories, commence connecting the corners of the shade sail to the fixing points.

Connect all points, using a ratchet tensioning tool if necessary to gain increased leverage. Stop tensioning when the shade sail is rigid with lilliputian or no creases. Caution: Do not over tension. Re-tension periodically if required.

Alarm

Your Coolaroo shade sail is designed to provide UV protection and condolement in domestic areas. When selecting the position for your shade canvass, ensure all fixing points are structurally audio and fixings are tightly secured. Inspect regularly. Prior to installing, consult your local council regarding edifice regulations which may apply in your surface area. Exposure to certain chemicals e.k, Chlorine can pb to the premature breakup of the fabric. Chemicals to be used on or effectually the fabric should be referred to Coolaroo prior to their utilise.

Practise not have fire or an open flame close to the cloth. Do not use your barbecue under the shade structure.

Intendance Instructions

Your shade sheet(s) may exist cleaned at any time using a solution of mild detergent and h2o. Apply the solution with a sponge or a very soft castor. Allow the solution stand on the material for 10 minutes and rinse thoroughly with water from your garden hose.

DO NOT put the fabric in your washing auto, clothes drier, or scrub information technology with a stiff castor, scouring pad, or an annoying cleaner.

For more information most shade sails check out our articles on choosing the right shade sail and DIY shade fabric installation.

Find specific instructions on how to install the Coolaroo three.6 10 3.6 Triangle Sail Shade here.

Related Articles